A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
This article which follows involving How to Install a Bathtub Yourself is absolutely motivating. You should see for yourself.
Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old tub is easily available, the project can move speedily; if you need to open up a wall to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have certified yourself for the work as well as fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This article will aid you install a new bath tub in your shower room if you have actually already purchased a brand-new bathtub and don't require to change the setup of your previous supply of water pipes.
Your devices and also product list should comprise the following:
Preparing for the Installation
Firstly, the supporting framework supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile faucet port to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and also inspect all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub needs to wait up until the bathtub has actually been utilized at the very least when as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Secure the faucet in position with the producer supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous kind must be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, triggering the water to permeate the wall surface between the bathroom and also the tiling, causing complications with moisture as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as installations. They are sold in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealant can crack rather early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that editorial on Installing A Bathtub through an acquaintance on our other web blog. In case you appreciated our post plz be sure to pass it around. We value reading our article about Installing A Bathtub.
Top service? Contact. Report this page